CAM-WOOD IAT-620-150HX FINGER JOINTER (MEDIUM PRODUCTION)


For Immediate Help Contact:
Louis Sicotte
(800) 374-5009 ext. 329
Intl. +1 (704) 841-2001
louis.sicotte@exfactory.com
If not available, try his/her backup:
Dan Wolters ext.376
dan.wolters@exfactory.com
}
Brand:  

CAM-WOOD

Model:   IAT-620-150HX
Category:  

FINGER JOINTERS

Machine Type:  

FINGER JOINTER (MEDIUM PRODUCTION)

Year of Mfg.:   2023
Condition:   Brand New w/Warranty  
Elect./Voltage:   480 V, 60 Cy, 3 Ph.
EXF #:   FJ-300021
List Price:   $ 165,000  
Our Price:   $ 149,500 USD     (Convert)
Financing: $ 2,988 National Capital Leasing
Description:    (view full)

CAM-WOOD IAT 620-150HX INVERTER DRIVEN FINGER JOINT SYSTEM 

Lay-Up and Block-Staging Infeed Conveyor: 

  • 24" Wide x 31.5" long belt conveyor powered with 1/2 HP motors. The conveyor is controlled by the operating and system. Feeds at a constant rate of 180 FPM. Block delivery is controlled by the operator and machine system criteria to feed the Shaper. The conveyor facilitates keeping the system full and productive.
     
    FSR-62I Right Hand Inverter Type Finger Joint Shaper: 
  • Feed table is 24" wide and accepts blocks from 6" to 31.5" long x 5/8" to 6" wide.  Shaper spindle is driven by a 20 HP motor and is equipped with provisions for vertical adjustment of 20 mm up and 20 mm down. Spindle diameter is 50 mm and runs at 6,600 RPM.  8-1/4” maximum shaper cutterhead diameter - without knives.
  • 5 HP - 4,800 RPM Cutoff and trim saw; accepts 10" dia. x 100 tooth x 5 mm blades.  2 HP - 2,850 RPM Scoring saw, accepts 7" dia. x 50 tooth x 5 mm blades.
  • Conveyor powered by 1/2 HP motor. 
  • Table movement is inverter driven; powered by a 3 HP inverter motor with cycle speeds from 1 to 4 cycles per minute. Motor senses load and varies travel as needed. 
     
    TC-62 Single Table Transfer Conveyor to the 2nd (Left Hand) Shaper: 
  • 24" Wide x 31.5" long belt conveyor. Powered with (1) 1/2 HP motor.  Controlled by system criteria.  Feeds at a constant rate of 180 FPM.
     
    FSL-62I Left Hand Inverter Type Finger Joint Shaper with Glue Extruder:
  • Feed table is 24" wide and accepts blocks from 6" to 31.5" long x 5/8" to 6" wide.  Shaper spindle is driven by a 20 HP motor.  Spindle diameter is 50 mm and runs at 6,600 RPM. 8-1/4" Maximum shaper cutterhead diameter - without knives.
  • 10 HP - 4,800 RPM Cutoff and trim saw; accepts 10" dia. x 100 tooth x 5 mm blades. 2 HP motor powers a top and a 2nd 2 HP motor powers a bottom scoring saw, both running at 2,850 RPM; accepts 7" dia. x 50 tooth x 5 mm blades.
  • Conveyer powered by 1/2 HP motor. Table movement is Inverter driven; powered by a 3 HP + 3 HP inverter motor with cycle speeds from 1 to 4 cycles/Min. Motor senses load and vary travel as needed.  Speed is controlled by system criteria.
     Injection Type Glue Applicator: 
  •  Extrudes adhesive into the fingers without a messy runoff. 6" Comb height is standard.  Finger pitch 4 mm, 10 - 12 mm finger length is standard equipment (special sizes available as optional equipment)
     
    STC-62A Single Table Conveyor Belt to the Assembly Section: 
  • 24" Wide x 31.5" long belt conveyor. Powered with (1) 1/2 HP motor. Controlled by system criteria. Feeding at a constant rate of 180 FPM.
     
    FJ-500A (198") Assembly Press with Cut-Off Saw: 
  • Capacity from 1" to 6” wide x 1/2" to 3" high x and from 6' to 16-1/2' long. motor powers the upper and lower pre-assembly driven by (2) 2 HP motor .
  • 5 HP infeed inverter drive. In-feed speed from 30 to 230 FPM. Speed is controlled by system criteria.
  • 5 HP - 2,850 RPM Cutoff saw accepts 14" dia. x 120 tooth x 4 mm kerf blade. Cutoff Saw can be set for up to (3) lengths. 5 HP Hydraulic power pack for the final squeeze. Capacity from 1 to 4 table loads per minute.

    Optional Equipment:
     

  • 8” Finished Width at Assembly Press, (horizontal joints only), add  $9,900
  • SFJ-IL-40 40” High-Speed Material Infeed Conveyor System, add $12,600.00



  • Infinite length for assemble ...Price on request
Special Note:
Comment: What a great Finger Jointer for an amazing price!
Written By: Jeff Terrill  
*Dimensions:Available from product manager
*Weight:Please call
*Dimensions & Weight data are based on 3rd party information and could be incorrect; please verify & confirm if accurate dimensions & weight are required.