Description:
CAM-WOOD TYPE F1, MODEL FAH 6” X 20’ HORIZONTAL FULLY AUTOMATIC FINGER JOINT SYSTEM - SINGLE CHAIN TYPE
MECHANICAL SPECIFICATIONS FOR THE FEED SYSTEM:
- Operating speed: 120 to 150 lugs per minute
- Intermittent feed motor: 2HP + 1:25
- Feed chain motor: 30 HP (20kw) Servo Drive
(C2) MECHANICAL SPECIFICATIONS: RIGHT-SIDE SHAPER:
- Cutterhead Motor: 25 HP
- Spindle size: 2-3/4” (70mm)
- Maximum cutterhead body diameter: 10”
- Cutterhead speed: 5,500 RPM at 60Hz
- Trim Saw Motor: 15 HP
- Trim Saw blade size: 12” (305mm) x 80 Tooth x 5mm kerf
- Cut-off saw Speed: 4,300 RPM
- Scoring saw motor: 3HP
- Scoring saw blade: 7” (180mm) x 50 Tooth x 5mm
- Scoring saw spindle speed: 4,200 RPM
- Holddown rise and lower motor: 1/2 HP
(C3) MECHANICAL SPECIFICATIONS: LEFT-SIDE SHAPER:
- Cutterhead Motor: 25 HP
- Spindle size: 2-3/4” (70mm)
- Maximum cutterhead body diameter: 10”
- Cutterhead speed: 5,500 RPM at 60Hz
- Trim Saw Motor: 15 HP
- Trim Saw blade size: 12” (305mm) x 80 Tooth x 5mm kerf
- Cut-off saw Speed: 4,300 RPM
- Scoring saw motor: 3HP
- Scoring saw blade: 7” (180mm) x 50 Tooth x 5mm
- Scoring saw spindle speed: 4,200 RPM
- Holddown rise and lower motor: 1/2 HP
- Glue Application by GLUE COMB
- Standard glue height: 6” high, 3.8mm pitch 3.8mm. Finger lengths from 10 to 12mm (Other lengths available)
(K) MECHANICAL SPECIFICATIONS: SHAPER OUT-FEED:
- Speed: 230 FPM
- Feed Motor: (1) 3 HP
- Vacuum device blower with 3” Vacuum port: 5HP
(G) MECHANICAL SPECIFICATIONS: PRE-JOINT ASSEMBLY:
- Feed chain drive: (2) 3HP motors
- In-feed Inverter: (1) 7-1/2 HP
- Chain type: Flat top double chain
- Feeding speeds from 30 to 300 FPM
(H) MECHANICAL SPECIFICATIONS: 20’ (6.2M) ASSEMBLY PRESS:
- Working dimension: 3/4” to 6” wide x 0.60” to 3” high x up to 20’ long
- Upper & lower roll power: (2) 2HP motors
- In-feed Inverter: 7-1/2 HP
- In-feed speed: 30 to 300 FPM
- PROGRAMMABLE Cut-off saw power: 5HP
- Cut-off Blade dimensions: 14” dia. x 120 Tooth x 1” bore
- Cut-off saw speed: 2,850 RPM
- Hydraulic power: 5HP (With high speed oil tank)
- Cycle Speed: 1 to 8 cycles per minute
PRODUCTION CAPACITY - PARAMETERS:
- Based on a 480-minute shift
- Finger length to customer’s specifications
- Average infeed length at the shaper section is 20”
- Average block cross section is 2” x 4”
- Chain speed at the Shaper sections is 150 lugs per minute
- Press capacity is (8) 20’ loads per minute (maximum)
CAPACITY OF THE SHAPERS WHEN FINGER JOINTING 2” X 4” x 20" BLOCKS
- (120) Blocks per minute
- x 20” Average infeed length
- x 480 Minutes per shift
- x 0.8 Rate of utilization = 76,800 lineal feet per shift
CAPACITY OF THE PRESS ASSEMBLING 20’ LENGTHS:
- (8) Assembled lengths per minute
- X 20’ Per minute
- X 480 Minutes per shift
- X 0.8 Rate of utilization = 66,440 lineal feet per shift
- NOTE: If using the cutoff saw for multi-section pressing, capacity is reduced.
SUGGESTED BLOCK REQUIREMENTS SUGGESTED FOR BEST RESULTS:
- Block lengths from 6” to 40”
NOTE: Block lengths must be at least 50% longer than the block width being run.
- If a block is 6” wide, the shortest length possible must be 50% greater, or 9” long
Examples:
- When running of 4” wide blocks, the shortest block possible is 6” long
- When running of 3” wide blocks, the shortest block possible is 4-1/2” long
- Block thickness from 0.06” to 2.36”
- Block widths from 1” to 6-1/4”
- Assembled out-feed lengths from 10’ to 20’
- Glue type is PVAC
- Wood species can be soft or hardwood
- Preferred moisture is 8 to 12%
- For best results, blocks should be surfaced 4-sides to a tolerance of ±0.2mm
- Blocks require 90-degree right angles and should be clear and straight
- Block lengths should not vary more than 50%
TO BE PROVIDED LOCALLY:
- Electrical power supply to switch cabinet
- Total Power demand: 65 KW, 86 HP
- Constant voltage with deviations of max. 5%
- Temperature range for computer control should not exceeding 95°F
- Maximum relative air humidity for control system computer 65%
- Dust exhaust system: (V=30M/S at a low pressure of 12M BAR)
- Compressed air connection to plant units: 6~8 KG/CM2 – 8BAR Cable, collecting duct
- Hydraulic oil
- Skilled operating and maintenance personnel
- Noise control
- Well-lit d working environment
- Computer cable if machine is with remote monitoring
- Dust Collection: (3) each 4” and (4) each 8” and 6,800 FM
- Compressor air requirement request: 30 HP with 30-gallon air receiver and 80 to 90 PSI
NOTES:
- Training and installation are optional.
- Customer is responsible for local regulations and connecting utilities
- Price is F.O.B. Los Angeles, CA
- Tooling, rigging and freight are not included.
- Payment Terms are 50% deposit with order, balance prior to shipping.
- Questions? Please call Jeff Terrill at 503.535.9343 or e-mail jeff.terrill@exfactory.com
|