Description:
CAM-WOOD TYPE IAT, MODEL 620 Vertical & Horizontal Finger Jointer - consisting of the following segments:
DTC-62 Twin Infeed Conveyor:
- Operator fills the width of the 1st conveyor with blocks placed on edge. 1st Conveyor is controlled by the operator, feeding the 2nd buffer conveyor. Combined, the (2) conveyors facilitate keeping the system full and productive
- Each Conveyor is 24" wide x 40" long
- Powered with (2) 1/2 HP motors.
- Controlled by the system.
- Feeding at a constant rate of 180 FPM
FSR-62I Right Hand Inverter Type Finger Joint Shaper:
- Feed table is 24" wide and accepts blocks from 6" to 40" long x 1/2" to 6" wide
- Shaper spindle is driven by a 20 HP motor
- Spindle diameter is 50 mm and runs at 6,600 RPM
- 6.3" Maximum shaper cutterhead diameter - without knives
- 10 HP - 4,800 RPM Cutoff and trim saw; accepts 10" dia. x 100 tooth x 5 mm blades
- 2 HP - 2,850 RPM Scoring saw, accepts 7" dia. x 50 tooth x 5 mm blades
- Conveyer powered by 1/2 HP motor
- Table movement is Inverter driven; powered by a 3 HP inverter motor with cycle speeds from 1 to 4 cycles per minute. Motor senses load and varies travel as needed
STC-62A Single Table Transfer Conveyor:
- 24" Wide x 40" long
- Powered with (2) 1/2 HP motors.
- Controlled by the system
- Feeding at a constant rate of 180 FPM
FSL-62I Left Hand Inverter Type Finger Joint Shaper with Glue Extruder:
- Feed table is 24" wide and accepts blocks from 6" to 40" long x 1/2" to 6" wide
- Shaper spindle is driven by a 20 HP motor
- Spindle diameter is 50mm and runs at 6,600 RPM
- 6.3" Maximum shaper cutterhead diameter - without knives
- 10 HP - 4,800 RPM Cutoff and trim saw; accepts 10" dia. x 100 tooth x 5 mm blades
- 2 HP - 2,850 RPM Scoring saw, accepts 7" dia. x 50 tooth x 5 mm blades
- Conveyer powered by 1/2 HP motor
- Table movement is Inverter driven; powered by a 3 HP + 3HP inverter motor with cycle speeds from 1 to 4 cycles/Min. Motor senses load and varies travel as needed.
Includes Injection type Glue Applicator: - Extrudes adhesive into the fingers without messy runoff.
- 6" Comb height is standard
- Finger pitch 4 mm
- 10 - 12 mm finger length is standard equipment (special sizes made as options)
STC-62A Single Table Conveyor:
- 24" Wide x 40" long
- Powered with (2) 1/2 HP motors
- Controlled by the system
- Feeding at a constant rate of 180 FPM
FJ-500A (5) Meter (197") Assembly Press with Cut-Off Saw:
- Capacity is from 1" to 6" wide x 1/2" to 3" high x up to 16-1/2' long
- 2 HP motor powers the upper and lower pre-assembly rolls
- 5 HP infeed inverter drive
- In-feed speed from 30 to 230 FPM
- Speed is controlled by the system
- 5 HP - 2,850 RPM Cutoff saw accepts 14" dia. x 120 tooth x 4 mm kerf blades
- 5 HP Hydraulic power pack for final squeeze
- Capacity from 1 - 4 table loads per minute
Shaper Capacity:
- Shift = 480 minutes Finger length to buyer’s requirement
- 12” Average block length at the Shapers
- 1” x 2” Average block cross section
- Shaper max speed of (4) table strokes per minute
- Table speed will change as block widths become “wider” (or “taller” at the Shapers)
- Table accepts up to (24) blocks when vertical finger jointing 1” x 2” blocks
- Table accepts up to (12) blocks when horizontal finger jointing 1” x 2” blocks
- Number of timber pieces per shaper table (horizontal finger jointing 2" x 1")
- Capacity of the press is (4) table cycles per minute
- NOTE: Maximum capacity for "one-section pressing", the capacity is amended while "multi-section pressing".
- 16’-6" Press length
- 80% Rate of utilization
VERTICAL Finger Jointing: ...Capacity of the shaper when finger jointing 1” x 2” x 12” long blocks: (4) tables strokes per minute X 24-blocks per table load X 1’ average infeed block length x 480 Minutes per shift X 0.8 rate of utilization = 36,200 lineal feet per shift
HORIZONTAL Finger Jointing w/2 operators: ...Capacity of the shaper when finger jointing 1” x 2” x 12” long blocks: (4) table strokes per minute X 12 blocks per table load x 1’ average infeed block length x 480 Minutes per shift X 0.8 rate of utilization = 18,100 lineal feet per shift
Capacity of the Press w/2 operators: - (4) Table Loads per Min x 16’-6" min x 480 Min per shift x 0.8 rate of utilization = 25,500 lineal feet per shift
Incoming Block Requirements:
- Incoming block lengths from 6” to 40”
- Blocks must be at least 50% longer than their width
- Block thickness from 1/2” to 3"
- Block width from 1” to 6"
- Assembled lengths from 10’ to 16-6"
- For use with PVAC adhesives
- Works equally well with soft and hardwoods
- Moisture content from 8 to 12%
- Blocks to be surfaced (4) sides thru a Moulder or 4-sided Planer to ±0.2mm with 90° right angle corners
To Be Provided Locally by Customer:
- Electric power supply to electrical cabinet
- Constant voltage with deviations of 5% or less
- Temperature range for computer control should not exceed 95°F
- Maximum r humidity for computer control system under 65%
- Hydraulic oil
- Skilled operating and maintenance personnel
- Total electricity demand: 63.75 KW, 85 HP
- 30 HP Compressor with a 50 to 60 gallon Air Receiver
|