HOME > CLAMP - CASE & FEED THRU > CC-300016 > RETURN

ERREGI TECHNOPRESS VR2 CASE CLAMP (AUTOMATIC FEED THROUGH)


For Immediate Help Contact:
Bob Bullin
(800) 374-5009 ext. 346
Intl. +1 (704) 841-2001
bob.bullin@exfactory.com
If not available, try his/her backup:
Tony Cornacchione ext.432
TCorn@exfactory.com
}
Brand:  

ERREGI

Model:   TECHNOPRESS VR2
Category:  

CLAMP - CASE & FEED THRU

Machine Type:  

CASE CLAMP (AUTOMATIC FEED THROUGH)

Year of Mfg.:   2023
Condition:   Brand New w/Warranty  
Elect./Voltage:   400 V, 50/60 Cy, 3 Ph.
EXF #:   CC-300016
List Price:   Please call  
Our Price:   Request Quote    
Description:    (view full)

ERREGI TECHNOPRESS VR2 Automatic "Self Adjusting" Feed Through Case Clamp + Optional Auto Stapling Unit

Once the piece of furniture is assembled on the in-feed table the operator starts the automatic cycle and the unit enters the machine.

Scanning photo cells devices automatically determine the length and height of the workpiece and send this information to the PLC. The conveyor moves the unit into position while automatically setting the clamping head with the end pressure shoes - The clamping cycle begins immediately providing a tight and square hold using dowels or other assembly hardware.

Specifications:


  • Min. / Max Working Height: 300 / 1,200 mm (11.8" / 48")
  •  Min. / Max Working Length: 300 / 2,500 mm (11.8" / 98")
  • Min. / Max Working Depth: 100 / 700 mm (3.9" / 27.5")

    Clamping:
    The clamping force can be adjusted from the control console.  Once the pressing time has elapsed, or the operator releases the clamp system, the part is fed out (unloading onto out-feed conveyor, optional) and the machine is instantly ready to receive the next part of any size.

    Build Quality:
    The load bearing structure portal in welded tubular steel, inside of which the two mobile heads and the presser table run.
  • Motor Driven Presser Table & Mobile End Pressure Heads
  • Each Vertical Carriage (Mobile & Fixed)  is fitted with (3) Horizontal Pressure Bars with Programmable Positioning and Travel Up/Down by a Mechanical System
  • The Belt System is positioned on either side of the Machine to allow the Part to be clamped equally well, whether it is in the Center of the Conveyor Belt or at the Sides.
  •  98" Long Powered In-Feed Conveyor Belt with Alignment Guideway, Closed Loop Belt Rolls Driven by an Inverter-Controlled, Non-Synchronous Motor in Coated Aluminum (Included)

    Automatic Stapling System (Optional):
    The System is solidly fixed to the structure of the clamp in order to eliminate all alignment errors between the machine and the stapling machine normally found with two separate machines.
  • The X, Y,  & Z Axis travel by Brushless Motors and Drive Mechanisms
  • Staple Gun Rotation (C-Axis) is by a Brushless Motor
  • The Gun Angle (Off-Set Stapling) is Controlled by a Pneumatic Actuator
  •  The Control Console (10” Display) is the same for the Clamp and the Stapling System
  • 1,400 Staple Magazine Capacity

    Training & Installation are Additional




     
Special Note:
Comment: The Best Clamp Value on the Market!
Written By: Bob Bullin  
*Dimensions:140" L x 60" W x 102" H
*Weight:3,500 Lbs
*Dimensions & Weight data are based on 3rd party information and could be incorrect; please verify & confirm if accurate dimensions & weight are required.