|Model:||KAL 210 AMBITION|
EDGEBANDER (W/PRE-MILL & CORNER ROUNDING)
|Year of Mfg.:||2010|
|Condition:||Cleaned and checked|
|Elect./Voltage:||400 V, 50 Cy, 3 Ph.|
|Value New:||€ 210,000|
|Region:||EUROPE (Click for Regional Map)|
HOMAG AMBITION 2262 (aka KAL 210) PRODUCTION EDGEBANDER (W/PRE-MILL & CORNER ROUNDING) + PUR Glue system:
Edge thickness, coiled stock min/max, 0.4 - 3 mm (0.016. - 1/8"), straight edges, min/max. 0.3 - 6 mm (0.16 - 15/64"), panel thickness min/max. 8 - 60 mm (5/16" - 2-3/8").
Programmable via NC positioning motor.
Two vertical jointing spindles; KW 3.0 x 2 (HP 4.0 x 2), 150 Hz, 9,000 RPM Motors; equipped with panel blow-off device and SIKO digital counters for adjustments.
Vertical Coil Magazine, (2) positions.
Gluing System P.U.R. Glue:
QA 34 - PU 34 Quick Melt Overhead Extrusion Unit & roller applicator (reversible).
Pressure Section Type C:
Programmable NC motor positioning with (1) large 150 mm dia. driven & (6) idle rollers, pneumatically pressure control depending on edgbanding material used.
End Trimming Unit "HL-81":
kW 0.8 x 2 (HP 1.0 x 2) - 200 Hz, 12,000 RPM Motor ea. to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer 30 deg. to straight cut.
Top & bottom, kW 0.55 x 2 (HP 1.0 x 2) - 12,000 RPM ea. motor; Height adjustment with the top pressure-beam and tilting range +/- 1°.
Profile/Bevel/Corner Rounding Unit "FK11":
Multi function (2) motors to fine trim the edge overhangs at the work-piece upper and lower edge, as well as trimming around the front & rear vertical edge. kW 0.4 x 2 (HP 0.54 x 2) motor ea.
Profile/Bevel Scraping Unit "PN-10":
Top & bottom for thick PVC/ABS, pneumatically activated.
Flat Glue Scraper Unit:
Top & bottom, pneumatically activated to remove potential glue squeeze-out.
Buffing Unit "FA11":
Top & bottom edge buffing/polishing.
Operator & Machine Control:
HOMATIC PC 22 Power Control:
Controller functions in Windows environment and features: Keypad w/LCD flat-screen display, fault diagnostic, OS9 real-time operating system.
Hand-held control pendant reaching to the out-feed end of the machine, very useful for set-up and testing new programs.
From 18 - 25 MPM (59 ~ 82 FPM); 80 mm feed trackpads, and V-groove belt on top pressure beam which is motorized; motorized raising & lowering of top pressure beam through program selection.
(2) For "anti-sticking" (1) in-feed side of the machine, (1) prior to Buffing Unit for edge polishing.
SIKO Digital adjustments; electronic DC brakes on all trim motors, sound cabins for all trim workstations, standard adjustable outboard panel support with additional floor supports for heavy panels. Transformer to supply 400 Volt to the machine
Narrow Parts In-Feed device, guided on round steel bar with linear bearings to allow Very Narrow Parts being introduced under the hold-down beam at 90°. The device can be flipped out of the way if not needed. Very helpful to feed narrow drawer parts etc.
EX-FACTORY’s Logistic Department is experienced and setup to provide “Full Service Logistic” from Overseas Suppliers to your Door. …Packaging, Container Loading, Ocean Freight, Marine Insurance (door to door), US or Canadian Customs, Duty and domestic shipping to your Plant Door.
|Comment:||This HOMAG Production Edgebander KAL 210 Ambition 2262 has all the latest features to produce "High Quality" product|
|Written By:||Karl Balg|
|*Dimensions:||295" L x 40" W x 72" H|
*Dimensions & Weight data are based on 3rd party information and could be incorrect; please verify & confirm if accurate dimensions & weight are required.