You are not logged in.    Login  |  Register  |  Help
 
 



Additional Photos
We are awaiting video for this item from the principals. Click here to view all literature

For Immediate Answers Contact:
Jeff Terrill
 
(800) 374-5009 ext. 349
Intl. +1 (704) 841-2001
jeff.terrill@exfactory.com





If not available, try his/her backup:
Louis Sicotte at ext ...329
louis.sicotte@exfactory.com





EXF #: EM-010002
Brand/Model:

CANTEK "CFS-100/EM-12"

Machine Type:

DEFECTOR & END MATCHER/FINGER JOINT BLOCK

Condition: Brand New w/Warranty
Elect./Voltage: 230/460 V, 60 Cy, 3 Ph.
List Price: $ 150,000
Our Price: Please Call     (Convert)
Financing: National Capital Leasing
Description:
CANTEK MODEL CFS100 / EM-12 DEFECT SAW AND END-MATCHING SYSTEM: Consisting of a Cantek model CFS-100 Optimizing Cut-Off Saw followed by a Cantek Model EM 12 Through-Feed End Matcher and with the following specifications and features:

  • CANTEK MODEL CFS-100 OPTIMIZING CUT-OFF SAW
  • Up to 3.2" x 12" cutting capacity with 18" x 30mm bore sawblade is driven by a 10 HP motor driving the saw spindle at 3,200 RPM; 2.7 HP serve drive feed system drives the stock up to 260 FPM; 0.787" min. distance between crayon marks; requires 75 to 80 PSI at the saw and 100 to 120 PSI at defect blow-off station. Machine comes completely wired and programmed.
  • Machine is ideal for separating crayon marked waste zones from useable material before entering a feed-thru End Matcher; provides 3 times greater production than manual cut-off saws.; 5% + material recovery (yield increase) over manual cutting; compact and user-friendly design; controller adopts an industrial grade computer that employs a 32-bit floating-point DSP system and features flash and battery backup SRAM for double security; superior to conventional PC-based controls, it can fully eliminate the machine going down or being damaged due to a poor environment, such as, unstable voltage, high temperature, sawdust, etc.
  • With defect blow-off system combined with computerized logic control permits the blow-off time and the length of defect to be set as desired; provides efficient defect removal and eliminates defects from bumping against the sawblade, resulting in the machine going down or sawblade damage.
  • Computer control provides easy and fast maintenance; feed system driven by a servo motor for fast and accurate motion and position control; max. feed speed up to 260 FPM; cutting rate up to 80 cuts per minute with cutting accuracy within approx. ±1mm /0.40"; control employs a touch screen for easy learning and operation; new machine design features maximum maintenance convenience; high quality electric components provide maximum dependability; safety guards for maximum operator protection; 48" long infeed table standard - longer available option; 18" carbide blade included.
  • (5) Cutting modes include:
  • Adjustable end cuts to a max. of 10mm (.4")
  • Fixed length of cutting mode
  • Sequential cutting mode with (10) sets of cutting sizes held in memory (for sequential cutting mode only)
  • Cutting on fluorescent marks with double end trimming (perfect solution for end matching)
  • Reading fluorescent marks with double end trim, fixed length, random  length end match and finger joint block cutting.
  • CANTEK MODEL EM-12 END MATCHER
  • Continuous through-feed system; handles random length min. 10.6" to any length x 0.4" to 1.38" thickness x 12" width capacity; 295 FPM max. feed speed; average speed of 75 FPM based on 6'-6" board lengths; with 118" infeed and 98" outfeed tables; 5.5 HP shaper motors, 1 HP feed motor and 1/2 HP cutter stroke motor and 24-volt control system; clamping from top and outside side; 40mm spindle dia.; 6" dia. dust outlets; requires 85 PSI @ 12 CFM and a 12.5 total connected load at 230/460/575-volt, 60-cycle, 3-phase operation.
  • Standard features include: (1) set tongue & groove cutterheads, heavy duty self supporting main frame; compact design requires minimum floor space; capable of processing material as short as 11" to an unlimited length; variable speed through-feed system is controlled by frequency inverter; VFD mechanical drives for better control and elimination of surging as found with worn hydraulic drives; through-feed system allows the tongue to be cut simultaneously on the tail of one board and the leading edge of the next board; powered top urethane rolls and spring loaded bed rollers feed the material into position for processing; pneumatic side pressure system ensures the material is held square against the fence; safety and noise reduction enclosure.
Comments: UNIQUE DEFCT SAW AND END-MATCHER SYSTEM!!!
*Dimensions Available From Product Manager
*Weight: Please Call
*Dimensions & Weight data are based on 3rd party information and could be incorrect; please verify & confirm if accurate dimensions & weight are required.
Terms & Conditions AMEX